STAINLESS STEEL CROWNS
|
|
|
|
|
SHAN
LAL , DDS |
|
Director, Pre-clinical Programs |
|
Pediatric Dentistry |
SSC- Primary and
Permanent
|
|
|
Full coverage, metallic, definative
restorations |
|
Available as: pretrimmed (Unitek),
precontoured and festooned (Ni-Chro ION crowns) |
|
Durable and cost effective |
Indications for use of
SSC
|
|
|
Restoration of primary and young
permanent teeth with multiple carious surfaces. |
|
Class 2 lesions where the caries extend
beyond the anatomic line angles. |
|
Restoration of primary teeth after
pulpotomy or pulpectomy procedures. |
|
Hypoplastic teeth. |
|
Hereditary anomalies (D.I., A.I.) |
|
Pts. with special needs. |
|
As an abutment for space maintainers or
prosthetic appliances. |
|
|
|
|
|
|
|
|
Steps of preparation and
placement of SSC
|
|
|
Evaluate pre-operative occlusion |
|
Administer appropriate local
anesthesia* |
|
Place rubber dam (clamp adjacent tooth) |
|
Removal of caries (if present) |
|
Crown preparation |
|
Selection and trial placement of SSC |
|
Contour and crimp (if necessary) |
|
Evaluate post-operative occlusion |
|
Cementation |
|
|
Crown preparation
|
|
|
Occlusal reduction |
|
Inter-proximal |
|
Buccal and Lingual (limited to occl
1/3) |
Occlusal reduction
|
|
|
169L tapered fissure bur |
|
Place depth cuts and uniformly reduce
occlusal surface by 1-1.5mm. |
Occlusal Reduction
Proximal Reduction
|
|
|
169L tapered fissure or thin tapered
diamond bur. |
|
Break proximal contacts at appropriate
depth in single sweeping motion. |
|
Vertical proximal walls with slight
convergence in an occlusal direction. |
|
Feather-edge finish line. |
|
Common error - ledge formation. |
Proximal Reduction
SSC - Crown Preparation
Buccal and Lingual
Reduction
|
|
|
169L or diamond bur |
|
Limited to occlusal 1/3 as a 45º bevel. |
|
Round off all line angles. |
|
Occasionally, an exagerrated
mesio-buccal or cervical bulge may warrant more buccal and lingual reduction. |
|
|
Crown selection and
Try-in
|
|
|
SELECT smallest crown that restores
pre-existing proximal contacts. |
|
Occlusal dimensions of SSC should be
same as pre-op. tooth. |
|
Most commonly used molar SSC is size 4. |
|
PLACE or seat crown from lingual to
buccal. |
|
Push crown over the buccal bulge for a
snap fit. |
|
Check margins for close cervical
adaptation extending 1mm subgingivally. |
|
‘Blanching effect’ |
|
Remove dam and check occlusion. |
SSC - primary molar
|
|
|
Linguo-buccal seating of crown. |
|
Snap fit. |
Crimping and contouring
|
|
|
Crimping and Contouring involves
bending the gingival 1/3 of the
crown’s margins inward to establish a tight marginal fit and adaptation. |
|
Pliers - #114, 417 |
|
ION crowns require least adjustments. |
Crown cementation
|
|
|
Rinse and dry crown |
|
Prepare glass ionomer cement and fill
crown to 2/3 with all inner surfaces covered. |
|
Seat crown completely |
|
Remove excess cement from margins |
|
Rinse and floss inter-proximal areas |
|
Check occlusion |
Cementation
SSC - primary molar
SSC - Primary molar
SSC - Primary molar