IF NOT lasm .printx * CPXSYS.ASM * ENDIF ;NOT lasm ; KERMIT - (Celtic for "FREE") ; ; This is the CP/M-80 implementation of the Columbia University ; KERMIT file transfer protocol. ; ; Version 4.0 ; ; Copyright June 1981,1982,1983,1984,1985 ; Columbia University ; ; Originally written by Bill Catchings of the Columbia University Center for ; Computing Activities, 612 W. 115th St., New York, NY 10025. ; ; Contributions by Frank da Cruz, Daphne Tzoar, Bernie Eiben, ; Bruce Tanner, Nick Bush, Greg Small, Kimmo Laaksonen, Jeff Damens, and many ; others. ; ; This file contains the system-dependent code and data for KERMIT. ; It will be probably be broken into independent files to generate ; overlays for the various systems, one or more overlay possible ; from each file. For now, we will leave it in one piece. ; ; revision history: ; ; ; Edit 40, 28-Aug-89 by Mike Freeman of Bonneville Power Administration, ; P.O. Box 491, Vancouver WA 98666 USA, Telephone (206)690-2307: ; Home address: 301 N.E. 107th Street; Vancouver, WA 98685 USA ; Home telephone: (206)574-8221 ; added support for Hewlett-Packard HP-125 Business Assistant computer ; running a HP-modified CP/M Version 2.2; communications on ; DAta Comm 1 or Data Comm 2 (8th-bit quoting must be used on ; Data Comm 2 to transfer binary files as Data Comm 2 only supports ; a 7-bit data path); printer cannot be used with communications on ; Data Comm 2 (the printer port). ; edit 39, 4 August, 1987b by OBSchou for Charles Lasner re. DECMATE II ; fixes to set xon/off control off for the duration of Kermit-80. ; ; His header reads: ; ; IBM mode restore program ; ; This routine must be run after using CP4DMF (and KERMIT-80) to restore ; the normal handling of XON/XOFF; the user may also elect to cold-boot ; the DECMATE instead. ; ; acknowledgments and limitations. ; ; This program is based on DECMATE specific implementation details ; provided by Walt Lamia of DEC. It is of course, specific to DECMATE ; implementations of CP/M-80 for DECMATE II, III, III-plus, etc. ; ; usage consists of merely: ; ; CP4DMF run xon/xoff disable program ; KERMIT80 then run kermit ; ; CP4DMU run this program to restore normal XON ; ; unless CP4DMU is run following KERMIT-80, the normal handling of ; XON/XOFF provided by KERMIT-80 will not work (cold boot is another ; alternative). ; ; [Note - These edits now included in the init/de-init code] ; ; edit 38, 23 July, 1987 by OBSchou. Moved out commonly used code ; to CPXCOM.ASM, and adjusted this (ond other family) files accordingly. ; Also filtered out code now in other family files. ; ; edit 37 , 15 July 1987 by OBSchou for David Moore, who has submitted ; code for Teletek SYSTEMASTER (teletek) and for an ADM 22 terminal. ; ; edit 36 28 Jan 87 by OBSchou. ; Removed the printx etc and should only have this file if a system ; does not have a family file. ; ; edit 35 1st Dec 1986 by OBSchou. Added test for Amstrad PCW range (PCW) ; Links to CPXPCW.ASM, which was submitted by Ian Young, Lattice ; Logic Systems. ; ; edit 34 20 August by OBSchou for Brian Robertson, Aberdeen University: ; I have discovered a bug in my code for the BBC/Z80 version of Kermit. ; At startup the transmitter baud rate is read from the serial ULA. ; The TX and RX baud rates are then reset to this value and the ; value is stored in location 'baud:' for the STATUS (or SHOW) ; command. That is how it is supposed to work ! Unfortunately ; my code at present "misreads" the initial TX baud rate - there ; is some bit manipulation that needs to be done to extract the ; correct value. ; ; edit 33 30-May-86 OBSchou. Added two new enties to the overly. One for ; printer status and the other for the address of the family of ; computer using the overlay. If it is still in CPXSYS.ASM then it ; is a dollar only. ; ;edit 32, 27 May, 1986 by OBSchou Loughborough University for ; B Robertson, Aberdeen Univ. Computing Centre. Any mistakes my fault. ; Add support for APPLE II with serial cards based on the 6850 ACIA. ; Mod 380Z support to allow both MDS (5 1/4" discs) and FDS (8" discs) ; configurations. ; ; edit 31, 22 April, 1986, OBSchou. ; Kermit version 4.06 starts here. All previous edits have been ; put aside (leave in a BWR file?). Hived off some definitions ; to the CPSDEF.ASM file as that is where they belong. ; Start on splitting off individual ; systems from this huge file. It is done using the LINK facility ; LASM. We link to a collection of systems under CPXxxx.ASM. ; I have started with the systems I know, the Torch, Cifer and ; pci2651. These will all be held under CPXTOR.ASM ; ; ; Keep module name, edit number, and last revision date in memory. family: db 'CPXSYS.ASM (40) 28-Aug-89 $' ; now a family... ; ; Processor speed in units of 100KHz ; for cpt85xx, advance, apple,bbc,px8 & rm380z timing loop [12] IF rm380z cpuspd SET 40 ; 4.0 MHz CPU ENDIF; rm380z IF disc OR mmate OR s1008 OR access cpuspd SET 40 ; 4.0 MHz CPU ENDIF ;disc OR mmate OR s1008 OR access IF bbc ;[9] cpuspd SET 60 ; BBC with 6Mhz Z80 ENDIF;bbc ; the basics... IF gener batio EQU 056H ;I/O byte CON=BAT,LIST=CRT,READER=RDR,PUNCH=PTP defio EQU 095H ;I/O byte CON=CRT,LIST=LPT,READER=RDR,PUNCH=PTP crtio equ 01010101B ; use CRT: device ptrio equ 01010110B ; use PTR: device ttyio equ 00000000B ; use TTY: device uc1io equ 01010111B ; use UC1: device ur1io equ 01101010B ; use UR1: device ur2io equ 01111110B ; use UR2: device ENDIF;gener IF robin batio EQU 056H ;I/O byte CON=BAT,LIST=CRT,READER=RDR,PUNCH=PTP defio EQU 095H ;I/O byte CON=CRT,LIST=LPT,READER=RDR,PUNCH=PTP lptio EQU 054H ;I/O byte CON=TTY,LIST=CRT,READER=PTR,PUNCH=PTP gppio EQU 057H ;I/O byte CON=UC1,LIST=CRT,READER=RDR,PUNCH=PTP ENDIF;robin IF dmII OR bbc ;[22] batio EQU 042H ;I/O byte CON=BAT,LIST=CRT,READER=RDR defio EQU 081H ;I/O byte CON=CRT,LIST=LPT,READER=RDR ENDIF;dmII IF mikko batio EQU 10110010B ; I/O byte console => serial line defio EQU 10000001B ; I/O byte console => CRT and Keyboard ENDIF;mikko ; IF lobo ;[hh] mnport EQU 0F7E4H ;Modem data port A mnprts EQU 0F7E5H ;Modem status/conrtol port A baudrt EQU 0F7D0H ;Baud rate port A output EQU 04H ;Transmit buffer empty input EQU 01H ;Receive data available z80 SET TRUE ;a good z80, here ENDIF;lobo IF osi mnport EQU 0CF01H ;Modem data port mnprts EQU 0CF00H ;Modem status port output EQU 02H ;Transmitter empty input EQU 01H ;Input data available z80 SET FALSE ;I don't know... ENDIF;osi IF vector mnport EQU 04H ;Modem data port mnprts EQU 05H ;Modem status port output EQU 01H ;Transmitter empty input EQU 02H ;Input data available z80 SET FALSE ;I don't know... ENDIF;vector IF delphi ;[7] mnport EQU 22H ;[7] Modem data port mnprts EQU 23H ;[7] Modem status port output EQU 01H ;[7] Transmitter empty input EQU 02H ;[7] Input data available baudrt equ 29h ;[7] Baud rate port for channel 2 (default) z80 SET true ;[7] We're using the z80 side of the dual processor ENDIF;[7] delphi IF trs80 ;NEEDS display definition (e.g. trs80lb or trs80pt) mnport EQU 0F4H ;Modem data port (0F5H for port B) mnprts EQU 0F6H ;Modem status port (0F7H for port B) output EQU 04H ;Transmitter empty input EQU 01H ;Input data available z80 SET TRUE ;[hh] All TRS-80's but the CoCo ENDIF;trs80 IF teletek mnport EQU 00H ;Modem data port (02 for port B (console)) mnprts EQU 01H ;Modem status port (03 for port B (console)) baudrt EQU 08H ;ctc0 control port (09 for port B (console)) output EQU 04H ;Transmitter empty input EQU 01H ;Input data available z80 SET TRUE ;All Teleteks ENDIF;teletek IF osbrn1 ;Osborne 1 uses 6850 ACIA, but memory mapped. Derived from Apple. BAUDRT EQU 0EFC1H ;Memory location where baud rates are stored. OSTOP EQU 4000H ;Where we move OSMOVE to at startup OSPORT EQU 2A01H ;Communications Port. OSPRTS EQU 2A00H ;Communications Port Status. OUTPUT EQU 02H ;Output Buffer Empty. INPUT EQU 01H ;Input Register Full. OSBIN1 EQU 57H ;First Init Character for 6850 ACIA (Reset) ;(I would have thought 03, but prom code writes 57 there) OSBI12 EQU 55H ;Second Init Character for ACIA (8-bits, 1200) OSBI03 EQU 56H ;Second init char. for ACIA (8 bits, 300) ;(don't ask.. I don't know why SETUP writes 55 and 56 either) z80 SET TRUE ;[hh] a z80 here, also ENDIF;osbrn1 IF robin ;Those definitions below that are commented out are just for information ;***** NOT generally found in distributed documentation **** ;pbausl EQU 90H ;The Baud-Rate register. prntst EQU 49H ;Printer ;prndat EQU 48H contst EQU 41H ;Console ;condat EQU 40H gentst EQU 51H ;General port. ;gendat EQU 50H comtst EQU 59H ;COMM-Port ;comdat EQU 58H ;output EQU 01H ;Output ready bit. ;input EQU 02H ;Input ready bit. z80 SET TRUE ; This one's a Z80. ENDIF;robin IF s1008 ;[29] mnport equ 00 ;printer port data mnprts equ 01 ;printer port status output equ 4 ;transmitter ready input equ 2 ;receiver ready z80 equ FALSE ;not important ENDIF;s1008 [29] IF mmate ;[29] mnport EQU 89H ;MODEM data port mnprts EQU 8BH ;MODEM status/control port output EQU 04H ;Transmit buffer empty, ready to send input EQU 01H ;Receive data available baudrt EQU 93H ;MODEM baud rate port ;NOTE - also used for console z80 SET TRUE ENDIF;mmate [29] IF disc ;[29] mnport EQU 05 ;Discovery 83U port B data mnprts EQU 04 ;Discovery 83U port B status/command output EQU 04 ;Transmit buffer empty input EQU 01 ;Receiver ready z80 SET TRUE ENDIF;disc [29] IF cmemco ;[25] tuart EQU 020H ;TU-ART address mnport EQU tuart+1 ;Modem data port mnprts EQU tuart ;Modem status port output EQU 080H ;Transmitter empty input EQU 040H ;Input data available baudrt EQU tuart ;Baud rate port ;Note: Needs terminal definition z80 SET TRUE ;This one's a Z80. ENDIF;cmemco IF cpt85xx baudrt EQU 4Ch ; Baud rate generater (National MM5307) mnport EQU 4Bh ; Comm port data register (Intel 8251) mnprts EQU 4Ah ; Comm port command/status register output EQU 01h ; Transmitter buffer empty flag input EQU 02h ; Reciver buffer full flag TxEmpty EQU 04h ; Transmitter empty flag z80 SET FALSE ; It's really an 8080 [or 8085 ... same thing] ENDIF;cpt85xx IF mmdI ;Morrow MicroDecision - the single-board one mnport EQU 0FEH ;Morrow Printer UART data port mnprts EQU 0FFH ;Morrow Printer UART command/status output EQU 01H ;Output ready bit. input EQU 02H ;Input ready bit. ;Note: Needs terminal definition z80 SET FALSE ;I don't know... ENDIF;mmdI IF bbc ;[22] osbyte EQU 0FFF4H ; OS entry point osword EQU 0FFF1H ; " " " term EQU 0FFC8H ;Terminal mode OS entry z80 SET TRUE ENDIF;[22] bbc ;Two types of 380Z system IF rm380zm ;[27] MDS - 5 1/4" discs mnport EQU 0C8H ;Modem data port mnprts EQU 0C9H ;Modem status port ENDIF;[32] rm380zm IF rm380zf ;[32] FDS - 8" discs mnport EQU 0E8H ;Modem data port mnprts EQU 0E9H ;Modem status port ENDIF;[32] rm380zf IF rm380z ;[32] Common to both systems output EQU 01H ;Transmitter buffer empty input EQU 02H ;Input data available TxEmpty EQU 04h ;Transmitter empty flag z80 SET TRUE ENDIF;[22] rm380z IF px8 ; [29] z80 SET TRUE mnprts EQU 0dh ; used in sending a break ENDIF ;px8 [29] IF mdI ;Morrow Decision I - the big sucker mnport equ 48H ; Modem data port. mnprts equ 4DH ; Modem status port. output equ 20H ; Transmitter empty. input equ 1 ; Input data available. mbase equ 48H ; Base address of Multi I/O port ; selector area. grpsel equ 4FH ; Group select port. rbr equ 48H ; Read Data Buffer. group equ 1 ; Multi I/O Group byte for serial ports. congrp equ 1 ; Serial Port 1 for console mdmgrp equ 3 ; Serial Port 3 for modem. ; Following are needed for baud rate changes...[Toad Hall] dlm equ 49H ; Baud Rate Divisor (Most Sig Bit) dll equ 48H ; Baud Rate Divisor (Least Sig Bit) ier equ 49H ; Interrupt Enable Register lcr equ 4BH ; Line Control Register lsr equ 4DH ; Line Status Register msr equ 4EH ; Modem Status Register dlab equ 80H ; Divisor Latch Access Bit wls0 equ 1 ; Word Length Select Bit 0 wls1 equ 2 ; Word Length Select Bit 1 for 8 bit word stb equ 4 ; Stop bit count - 2 stop bits imask equ 0 ; Interrupt mask (all disabled) z80 SET TRUE ; This one's a Z80. ENDIF ;mdI NOTE: needs terminal definition. [Toad Hall] IF mikko sioac EQU 0FF12H ;SIO channel A register(s) address sioo3 EQU 01000001B ;SIO Write Reg. 3 original setup (?) ;RX 7 bits,synch mode bits 0,RX enable sion3 EQU 11001111B ;SIO Write Reg. 3 KERMIT setup ;RX 8 bits,synch mode bits 0,RX enable sioo4 EQU 01001111B ;SIO Write Reg. 4 original setup (?) ;X16 clock,8 bit synch(ignored), ;2stop bits,par even(on) sion4 EQU 01000100B ;SIO Write Reg. 4 KERMIT setup ;X16 clock,8 bit synch(ignored), ;1stop bit,par off sioo5 EQU 10101010B ;SIO Write Reg. 5 original setup (?) ;DTR,TX 7 bits,TX enable,RTS sion5 EQU 11101010B ;SIO Write Reg. 5 KERMIT setup ;DTR,TX 8 bits,TX enable,RTS txclk EQU 0FF30H ;Baud rate generator (CTC) for transmitter rxclk EQU 0FF31H ;Baud rate generator (CTC) for receiver chmask EQU 0F1F2H ;Mask byte address for SIO ch. A reception z80 SET TRUE ;It's got a SIO and a CTC, it must be a Z80 ENDIF;mikko IF access ;[29] mnport EQU 40H ;Modem data port A mnprts EQU 42H ;Modem status/conrtol port A output EQU 04H ;Transmit buffer empty input EQU 01H ;Receive data available z80 SET TRUE ;a good z80, here ENDIF;access [29] IF robin OR dmII z80 SET TRUE ; This one's a Z80 ENDIF;robin OR dmII IF hp125 ;[MF] z80 SET TRUE ;HP-125 uses a Z80 ENDIF;hp125 [MF] IF gener OR cpm3 ; To be truly generic, we must assume 8080. z80 SET FALSE ENDIF;gener OR cpm3 ; IF osi defesc EQU ']'-100O ;The default escape character. ENDIF; osi IF vector defesc EQU '~' ;Vector can't type ']'. ENDIF;vector IF mikko OR osbrn1 OR lobo defesc EQU '\'-100O ;The default is Control \ -- it's easier B.E. ENDIF;mikko OR osbrn1 OR lobo IF cpt85xx defesc EQU '\'-100O ;Still Control-\ (just ran out of room...) ENDIF;cpt85xx IF bbc OR rm380z OR px8 OR access OR S1008 ;[22] [29] defesc EQU '\'-100O ;Still Control-\ (just ran out of room...) ENDIF ;bbc OR rm380z OR px8 OR access OR s1008[29] IF trs80 defesc EQU '_'-100O ;CTRL-_ (Down-arrow on TRS-80 keyboard) ENDIF;trs80 ; Select initial setting for VT-52 emulation flag. IF vt52 ; If console looks like (or is) VT52 vtval EQU 0 ; we don't need VT52 emulation ENDIF;vt52 ; If none of the above, default to VT52-EMULATION ON. IF NOT (crt OR vt52 OR robin OR dmII OR vt100 OR hp125);[MF] vtval EQU 1 ENDIF;NOT (crt OR vt52 OR robin OR dmII OR vt100 OR hp125)[MF] ; sysxin - system dependent initialisation code, called from SYSINIT ; sysxin: IF dmII ; edit added by OBSchou for C. Lasner. If this dont work, tell me whats ; wrong, as I have no DMII or IBM to play with ; ; IBM mode fixup program ; ; This routine must be run before attempting to use KERMIT-80 with half ; duplex KERMIT implementations such as CMS-KERMIT, as the 6120 processor ; will otherwise "swallow" the XON character. ; ; acknowledgments and limitations. ; ; This program is based on DECMATE specific implementation details ; provided by Walt Lamia of DEC. It is of course, specific to DECMATE ; implementations of CP/M-80 for DECMATE II, III, III-plus, etc. ; ; usage consists of merely: ; ; CP4DMF run this program ; KERMIT80 then run kermit ; ; CP4DMU run companion program to restore normal XON ; ; unless CP4DMU is run following KERMIT-80, the normal handling of ; XON/XOFF provided by KERMIT-80 will not work (cold boot is another ; alternative). ; ; CP4DMF.ASM ; ; last edit: 12-jun-87 20:00:00 Charles J. Lasner (CJL) ;oboff equ 3fh ; offset of outbyt routine for 6120 ;prtctl equ 02h ; port control nocoxon equ 001h ; turn off comm. output XON lxi b,(nocoxon * 100h) + prtctl ; c/prtctl, b/no out. xon call outbyt ret ; and return ;outbyt has been catered for (in break routine) ENDIF ;dmII IF osbrn1 ;(Note now no longer needs code > 4000h as it is already there ; lxi d,ostop ;where we're moving it to ; lxi h,osmove ;what we're moving ; mvi b,osmct ;How many bytes we're moving ; call mover lda baudrt ; Find out what speed is current ani 1 mvi a,osbi03 ; assume 300 baud jz osstr1 mvi a,osbi12 ; nope, it's 1200. osstr1: sta speed ; save initial speed sta speed+1 ; as 16 bits, to match speed table entries mov d,a mov e,a ; get initial speed in DE call sysspd ;set up parity etc. ENDIF;osbrn1 IF cpt85xx mvi a,80h ; Send UART reset [force idle] by setting out baudrt ; bit 7 of baud rate I/O port lxi H,0f0fh ; Clear reset and default to 9600 baud [23] shld speed ; store current speed xchg call sysspd ; set default baud rate mvi a,4Eh ; Set UART mode to async 16x clock, 8 data out mnprts ; bits, no parity, and 1 stop bit mvi a,37h ; Set command to Tx enable, DTR on, Rx enable, out mnprts ; break off, error reset, and RTS on ENDIF ; cpt85x IF bbc ;[22] lxi d,modstr ; Set MODE 3 call prtstr mvi a,1 ; Set terminal mode on call term mvi a,0F2H ; Read current transmit speed lxi h,0FF00H ; .. 3 lsb of ULA register call osbyte ; FX242,0,255 mov a,l ani 7 ; Mask of 3 lsb ; ; Edit of July 22, 1986 by B Robertson, Aberdeen Univ. Computing Centre. ; Correct bug in sysinit for BBC - reads the initial baud rate at ; start up incorrectly. ; ; rar ; Reverse order of 3 lsb rar ; Bit2 now in bit0 jnc binit1 ; ori 2 ; Restore bit1 binit1: ana a ; Set sign bit as appropriate jp binit2 ; ori 4 ; Bit0 now in bit2 binit2: ani 7 ; Mask off unwanted bits ; End of Edit xri 7 ; Stored as 2's complement inr a sta speed ; Store 16 bit value sta speed+1 mov e,a ; Ensure RX and TX speeds are the same call sysspd ENDIF;[22] bbc IF rm380z ;[22] mvi e,11h ;Output ctrl-Q to clear autopaging call outcon ENDIF;[22] rm380z IF lobo ;[hh] lxi d,siotbl ;[hh] address of status table mvi c,siolen ;[hh] length of the table siolup: ;[hh] loop here for each command byte ldax d ;[hh] load first byte into A inx d ;[hh] index pointer to next bute sta mnprts ;[hh] send it to status port A sta mnprts+2 ;[hh] and to status port B dcr c ;[hh] decrement the counter jnz siolup ;[hh] loop back for more commands mvi a,05H ;[hh] value for 300 baud sta baudrt ;[hh] starting default for port A sta baudrt+4 ;[hh] and for port B sta speed ;[hh] tell program they're set mvi a,0E4H ;[hh] value for port A sta port ;[hh] tell program we've set this, too mvi a,0D0H ;[hh] port A baud rate value sta port+1 ;[hh] save this as well, for consistancy ENDIF ;lobo IF mikko lxi d,mintbl ;Address of KERMIT Reg values (what) mvi c,minlen ;Length of table (how many) lxi h,sioac ;Send data to ch. A SIO registers (to where) call movmik mvi a,0FFH ;Set ch. A mask to use all bits sta chmask ENDIF;mikko IF mdI lxi h,96 ;Default 1200 baud modem port speed shld speed ;Store as modem port speed call sysspd ;Initialize the port ENDIF;mdI [Toad Hall] IF cmemco ;[25] mvi a,01h ; Reset TU-ART out tuart+2 mvi a,90h ; Set default baud rate (2400), and 1 stop bit out tuart sta speed ; save for status display sta speed+1 ENDIF;cmemco IF delphi ;[7] ; ; shove the default baud rate (1200) in to the Delphi port address ; for the baud rate generator on port 2, the default port; save this ; value so we can tell what speed is selected. ; mvi a,07h ;[7] get value for 1200 baud out baudrt ;[7] set it for port 2 sta speed ;[7] save for status display sta speed+1 ENDIF;[7] delphi IF px8 ; [29] lda 0f6a9h ; get baud rate value set by CONFIG sta px8blk+4 ; put into parameter block mov h, a ; initialise global speed indicator mov l, a shld speed lhld 6 ; base of CP/M ; buffer starts at ovlend+8192, immediately after sector buffer ; We must also allow (800h) for the CCP as Kermit exits with a RET lxi d, ovlend+8192+800h ; calc buffer length ora a ; clear carry db 0edh, 52h ; sbc hl, de shld px8blk+2 call rsopen ENDIF ; px8 [29] IF disc ;[29] ;Initialization sequence for Discovery 83U port B ;Sets port to 9600 baud, 8 data bits, 1 stop bit, no parity mvi a,12 ;Register 12 out mnprts mvi a,11 ;Low byte of time constant for 9600 out mnprts mvi a,13 ;Register 13 out mnprts mvi a,0 ;High byte of time constant for 9600 out mnprts mvi a,14 ;Register 14 out mnprts mvi a,3 ;Enable baud rate generator out mnprts mvi a,11 ;Register 11 out mnprts mvi a,52h ;No Xtal, tclk=rclk=/trxc out=br gen out mnprts mvi a,4 ;Register 4 out mnprts mvi a,44h ;16x clock, 1 stop, no parity out mnprts mvi a,3 ;Register 3 out mnprts mvi a,71h ;rx 8 bit/ch, autoenable, rx enable out mnprts mvi a,5 ;Register 5 out mnprts mvi a,0eah ;tx 8 bit/ch, tx enable, rts out mnprts ENDIF;disc [29] ; ; IF mikko ;currently for MIKROMIKKO only ; copy command block into memory-mapped SIO. movmik: di ;disable interrupts movmk1: ldax d ;Get a register value mov m,a ;Output it inx d ;Next value dcr c ;Decrement counter jnz movmk1 ;Repeat until done ei ret ENDIF;mikko ; IF osbrn1 osmove: osflag equ 0EF08H ;Osborne 1 Bank-2 flag ; ; return modem status in A ; OSLDST: DI OUT 0 LDA osprts ;Read the status port OUT 1 EI ret ; ; set modem status from A ; OSSTST: DI OUT 0 STA osprts ;Write the control port jmp osstex ; ; read character from modem into A ; OSLDDA: DI OUT 0 LDA osport OUT 1 EI ret ; ; output character in A to modem ; OSSTDA: DI OUT 0 STA osport osstex: OUT 1 mvi a,1 sta osflag EI ret ENDIF;osbrn1 IF lobo ; List of commands to set up SIO channel A for asynchronous operation. siotbl: DB 18H ; Channel reset DB 18H ; another, in case register 0 wasn't selected DB 04H ; Select register 4 DB 44H ; 1 stop bit, clock*16 DB 01H ; Select register 1 DB 00H ; No interrupts enabled DB 03H ; Select register 3 DB 0C1H ; Rx enable, 8 bit Rx character DB 05H ; Select register 5 DB 0EAH ; Tx enable, 8 bit Tx character, ; raise DTR and RTS siolen equ $-siotbl ; length of command list ENDIF;lobo IF mikko ; command list to set SIO chip back to normal state miotbl: db 3 ;reg. 3 db sioo3 db 5 ;reg. 5 db sioo5 db 4 ;reg. 4 db sioo4 db 0 ;reselect reg. 0 miolen equ $-miotbl ;MikroMikko SIO table length (original values) ; command list to set up SIO chip for operation with Kermit mintbl: db 3 ;reg. 3 db sion3 db 5 ;reg. 5 db sion5 db 4 ;reg. 4 db sion4 db 0 ;reselect reg. 0 minlen equ $-mintbl ;MikroMikko SIO table length (KERMIT values) ENDIF;mikko IF bbc ;[22] modstr: db 16h,03h,'$' ; String to put screen into MODE 3 ENDIF IF px8 ; [29] rsget: mvi b, 50h jmp rsiox rsinst: mvi b, 30h jmp rsiox rsput: mvi b, 60h jmp rsiox rsoutst:mvi b, 40h jmp rsiox rserst: mvi b, 90h jmp rsiox rsopen: lxi h, px8blk ; copy px8blk to px8prm lxi d, px8prm lxi b, 9 call mover mvi b, 10h ; open code jmp rsiox rsclose:mvi b, 20h ; close code rsiox: lxi h, px8prm lxi d, 51h ; offset into BIOS jump table push h lhld 1 ; start of BIOS dad d xthl ; entry point on stack, px8prm addr in hl ret ; jump indirect px8prm: dw 0, 0 db 0, 0, 0, 0, 0 ; the param area is overwritten in rsopen px8blk: dw ovlend+8192 ; buffer address dw 0 ; buffer size - overwritten db 0 ; baud rate - overwritten db 3 ; 8 bits/char db 0 ; no parity, it is done internally db 1 ; 1 stop bit db 0cfh ; special bits - activate xon/xoff ; The documentation suggests that the xon/xoff bit is bit 4, i.e the pattern ; should be 0efh, but the top bit is omitted from the diagram. I will try ; clearing both bit 4 and bit 5. ENDIF ; px8 [29] IF hp125 ;[MF] lxi b,73ffh ;Prepare Data Comm 1 to call bdos ;Transfer eight-bit data lxi d,jbuf ;Point to bios jump-table vector lxi b,7effh ;Set up special subfunction code to call bdos ;Get rdr routine address lhld jbuf+3 ;Remember this address shld readin+1 ;for our eight-bit rdr routine mvi a,1 ;We want to write into the bios jump table sta jbuf+1 ;... lxi h,readin ;Point to our rdr routine (all 8 bits) shld jbuf+3 ;as new RDR routine lxi d,jbuf ;Point to jump vector argument block lxi b,7effh ;Set subfunction code to call bdos ;Substitute our rdr routine in dispatch table lxi h,mapon1 ;Make Data Comm 1 the default port shld port ;at program-start xchg ;Put in DE call prtstr ;Print escape sequences to connect ;DAta Comm 1 to rdr/punch ENDIF ;hp125 [MF] ret ; end of sysxin ; ; system-dependent termination processing ; If we've changed anything, this is our last chance to put it back. sysexit: IF dmII ; Edited by OBSchou for Charles Lasner. His bug fix now in Kermit-80: ; ; IBM mode restore program ; ; This routine must be run after using CP4DMF (and KERMIT-80) to restore ; the normal handling of XON/XOFF; the user may also elect to cold-boot ; the DECMATE instead. ; ; acknowledgments and limitations. ; ; This program is based on DECMATE specific implementation details ; provided by Walt Lamia of DEC. It is of course, specific to DECMATE ; implementations of CP/M-80 for DECMATE II, III, III-plus, etc. ; ; usage consists of merely: ; ; CP4DMF run xon/xoff disable program ; KERMIT80 then run kermit ; ; CP4DMU run this program to restore normal XON ; ; unless CP4DMU is run following KERMIT-80, the normal handling of ; XON/XOFF provided by KERMIT-80 will not work (cold boot is another ; alternative). ; ; CP4DMF.ASM ; ; last edit: 12-jun-87 20:00:00 Charles J. Lasner (CJL) ; coxon equ 000h ; enable comm. output XON ;oboff equ 3fh ; offset of outbyt routine for 6120 ;prtctl equ 02h ; port control lxi b,(coxon * 100h) + prtctl ; c/prtctl, b/with out. xon call outbyt ;[OBS] declared elswhere ret ; and return ENDIF ;dmII IF mikko lxi d,miotbl ;Load the adress of original reg values mvi c,miolen ;Length of table lxi h,sioac ;Send data to ch A SIO registers call movmik mvi a,07FH ;Set ch A mask to use just 7 bits sta chmask ENDIF;mikko IF teletek ;Note - This code was handwritten onto the lising I was sent, with the ; comment that David had just thought of the code, so it was ; not on the listing. If you have problems I suggest you ; comment out these few lines. ;Bertil Schou. ; di mvi a,47h ; reset baud rate to 9600 out baudrt mvi a,08h out baudrt ei ENDIF ;teletek IF cpt85xx mvi a,80h ; Reset (force idle) the 8251 UART via bit 7 out baudrt ; of the baud rate generater port mvi a,00h ; and turn off the baud rate generater out baudrt ENDIF;cpt85xx IF bbc ;[22] mvi a,0 ; Turn off terminal mode call term ENDIF;[22] bbc IF px8 ;[29] call rsclose ENDIF ;px8 [29] IF hp125 ;[MF] lxi b,74ffh ;Set subfunction code to call bdos ;Reset Data Comm 1 for 7-bit data lhld readin+1 ;Get original rdr routine address shld jbuf+3 ;and store in jump vector lxi d,jbuf ;Point to jump vector lxi b,7effh ;Set subfunction code to call bdos ;Put original rdr routine back in bios ;dispatch table lxi d,mapoff ;Point to escape sequences to call prtstr ;Turn off Data Comm 1/2 mappings ENDIF ;hp125 [MF] ret ; ; system-dependent processing for start of CONNECT command ; syscon: IF robin OR trs80 OR cpt85xx ;For Robin/TRS80/CPT-85xx, add some more info lxi d,conmsg ; about obscure key combinations call prtstr ENDIF;robin OR trs80 OR cpt85xx IF osbrn1 ;*** This is Software dependent *** lhld 1 ;Modify back-arrow code to DELETE mvi l,0 ;Get BIOS-start address lxi d,85H ;Adress for key-code = XX85H dad d mov e,m ;Get it in DE inx h mov d,m xchg ;Memory pointer to HL mvi m,del ;modify the code ENDIF;osbrn1 ret conmsg: ; Messages printed when entering transparent (CONNECT) mode: IF robin ; for Robin, control-S key is hidden db ' (Type Left Arrow to send CTRL-S)',cr,lf,'$' ENDIF;robin IF trs80 ; for TRS-80, the preferred escape key is hidden db ' (Control-_ is the Down-Arrow key on the TRS-80 keyboard)' db cr,lf,'$' ENDIF;trs80 IF cpt85xx ; for CPT-85xx, some graphics map "funny" to keyboard in CP/M db ' (Use CODE + SHIFT + 1/2 key to generate a Control-\)' db cr,lf,'$' ENDIF;cpt85xx ; ; syscls - system-dependent close routine ; called when exiting transparent session. ; syscls: IF osbrn1 lhld 1 ;Modify back-arrow code to BACKSPACE mvi l,0 ;Get BIOS address lxi d,85H ;Address for key-code =XX85H dad d mov e,m ;Get it in DE inx h mov d,m xchg ;Address to HL mvi m,bs ;Modify code ENDIF;osbrn1 ret ; ; sysinh - help for system-dependent special functions. ; called in response to ?, after listing all the ; system-independent escape sequences. ; sysinh: IF robin OR dmII OR cpt85xx OR lobo lxi d,inhlps ; we got options... call prtstr ; print them. ENDIF;robin OR dmII OR cpt85xx OR lobo IF bbc OR rm380z ; some more lxi d,inhlps ; we got options... call prtstr ; print them. ENDIF;[22] bbc OR rm380z IF px8 OR access OR mmate OR disc ;and more... lxi d,inhlps ; we got options... call prtstr ; print them. ENDIF ;px8 OR access OR mmate OR disc ret ;additional, system-dependent help for transparent mode ; (two-character escape sequences) inhlps: IF robin OR dmII OR cpt85xx OR lobo db cr,lf,'B Transmit a BREAK' ENDIF;robin OR dmII OR cpt85xx OR lobo IF bbc OR rm380z db cr,lf,'B Transmit a BREAK' ENDIF;bbc OR rm380z IF px8 OR access OR mmate db cr,lf,'B Transmit a BREAK' ENDIF ;px8 OR access OR mmate IF disc ;[29] [32] db cr,lf,'B Transmit a 300ms BREAK' db cr,lf,'L Transmit a 5 second BREAK' ENDIF;disc [29] IF lobo db cr,lf,'D Drop the line' ENDIF;lobo db '$' ;[hh] table terminator ; ; sysint - system dependent special functions ; called when transparent escape character has been typed; ; the second character of the sequence is in A (and in B). ; returns: ; non-skip: sequence has been processed ; skip: sequence was not recognized sysint: ani 137O ; convert lower case to upper, for testing... IF robin OR dmII OR cpt85xx OR lobo cpi 'B' ; send break? jz sendbr ; yes, go do it. return nonskip when through. ENDIF;robin OR dmII OR cpt85xx OR lobo IF bbc OR rm380z ; [22] [25] ... some more cpi 'B' ; send break? jz sendbr ; yes, go do it. return nonskip when through. ENDIF; bbc OR rm380z IF px8 OR access OR mmate ;[28] [29] and anothers cpi 'B' ; send break? jz sendbr ; yes, go do it. return nonskip when through. ENDIF ; px8 OR access OR mmate [28] [29] IF lobo ;[hh] cpi 'D' ;[hh] disconnect? jz discon ;[hh] yes, go do it. nonskip return when done. ENDIF ;lobo IF disc ;[29] cpi 'B' ;Send short break? jz sendbr cpi 'L' ;Send long break? jz sendlbr ENDIF;disc [29] jmp rskp ; take skip return - command not recognized. ; IF robin ;Definitions & code to send a BREAK (ungenerically, no other way). comctl equ 59h ;VT180 communications port crtctl equ 41h ;VT180 crt port ;VT180 serial port command bits txe equ 1 ;transmit enable dtr equ 2 ;dtr on rxe equ 4 ;rx enable sndbrk equ 8 rerr equ 10h ;reset error rts equ 20h ;RTS on reset equ 40h ;port reset ;Send a break to the communications port. ; sendbr: lxi h,38500 ;250 ms(?) lda prtadr ;Get address of selected port mov c,a ;Into C mvi a,sndbrk+dtr ; OUT C,A ;Want to send to port addressed by C db 0EDH,079H ;Op code for above instruction sndbr1: dcx h ;timing loop... mov a,l ora h jnz sndbr1 ;...until over lda prtadr ;Get the address for the port mov c,a ;Into C mvi a,txe+dtr+rxe+rerr+rts ;enable tr/rc, dtr, reset error ; out c,a ;Z-80 only instruction db 0EDH,079H ;Op code for above instruction out contst ;reset ports ret ENDIF;robin ; IF dmII ;[jd] this added to send break on DECmate ; DECmate command codes for 6120 I/O processor oboff equ 3fh ; offset of outbyt routine for 6120 prtctl equ 02h ; port control brdat equ 06h ; data to tell 6120 to send a break brdur equ 30 ; duration, 30 = 300 ms. sendbr: lxi b,(brdat * 100h) + prtctl ; c/prtctl, b/brdat call outbyt lxi b,brdur*100h ; b/duration, c/0 ; fall through into outbyt outbyt: lhld 1 ; get warm boot address lxi d,oboff ; offset of outbyt routine dad d ; compute address pchl ; branch there (a callret) ENDIF;dmII ; IF access OR mmate ;[cjc] send break on Kaypro [29] ; Officially, a "break" is 300 milliseconds of "space" (idle line is ; "mark"). (or maybe 200 milliseconds; I forget.) The timing isn't ; usually that critical, but we'll make an attempt, at least. Sending ; too long a break can cause some modems to hang up. sendbr: ; First, make sure the transmitter is really empty. (The SIO sets ; "transmitter buffer empty" when it can accept another character; ; the previous character is still being shifted onto the line. ; Another status bit, "all done", is set to indicate that the ; transmitter is really idle. sndbr1: mvi a,1 ; select Read Register 1 out mnprts in mnprts ; read the contents ani 1 ; test "all done" flag jz sndbr1 ; loop until it's nonzero. ; ; Next, set the "send break" bit to start the transmitter spacing. mvi a,5 ; select Write Register 5 out mnprts mvi a,0FAH ; Tx enable, 8 bit Tx character, Send Break, out mnprts ; DTR and RTS on. ; ; Now, delay for 30 hundredths of a second mvi a,30 ; delay count call delay ; ; Time's up. Put transmitter back in normal state (data byte is the ; same as the one in siotbl: for Write Register 5) and return. mvi a,5 ; select Write Register 5 out mnprts mvi a,0EAH ; Tx enable, 8 bit Tx character, out mnprts ; DTR and RTS on. ret ; done. ENDIF;access OR mmate [29] IF lobo ;[hh] This routine sends a break tone or disconnects a modem ; (those that respond to it) by setting the DTR line low ; for 300 ms. ; sendbr: mvi a,05H ;[hh] write register 5 call outctl ;[hh] send it to control port mvi a,0FAH ;[hh] value to send break tone jmp sndbr1 ;[hh] ; discon: mvi a,05H ;[hh] write register 5 call outctl ;[hh] send it to the control port mvi a,06AH ;[hh] DTR off and break tone on sndbr1: call outctl ;[hh] send to control port mvi a,30 ;[hh] delay count for 300 ms. call delay ;[hh] wait a while... mvi a,05H ;[hh] write register 5 call outctl ;[hh] get it's attention mvi a,0EAH ;[hh] normal 8 bits, DTR on, RTS on, etc. call outctl ;[hh] restore SIO ret ; outctl: sta mnprts ;[hh] ret ENDIF ;lobo ; IF cpt85xx OR rm380z ;[lmj] [22] [25] sendbr: ; ; Ensure that the transmitter has finished sending buffered chars sndbr1: in mnprts ; get UART status ani TxEmpty ; everything sent? jz sndbr1 ; no, wait a bit more ; ; Begin sending a break by setting bit in UART command register mvi a,3Fh ; Set TxEna, DTR, RxEna, SBreak, ErrRst, RTS out mnprts ; ; Wait for 250 milliseconds (using hundredths second delay routine) mvi a,25 call delay ; ; Resume normal operation by clearing the SendBreak command bit mvi a,37h ;Set TxEna, DTR, RxEna, ErrRst, RTS out mnprts ; ret ;done ENDIF;cpt85xx OR rm380z IF px8 ; [29] sendbr: mvi a, 3fh ; set break bit out mnprts mvi a, 25 call delay ; wait 250 msec mvi a, 37h ; clear break bit out mnprts ret ENDIF ; px8 [29] ; IF bbc ;[22] sendbr: ; ; Ensure that the transmitter has finished sending buffered chars sndbr1: mvi a,96h ; get ACIA status mvi l,8 call osbyte ; *FX150,8 mov a,h ani 2 ; everything sent? jz sndbr1 ; no, wait a bit more ; ; Disable centisecond clock (system VIA) which interferes with break lxi h,0FE4Eh ; system VIA interrupt enable register mvi a,40H ; disable timer 1 call wrtiom ; write to I/O processor memory ; ; Begin sending a break by setting bit in ACIA control register mvi a,9Ch lxi h,9F60h ; Set Rxint, Txint, Break, RTS call osbyte ; *FX 156,96,159 ; ; Wait for 250 milliseconds (using hundredths second delay routine) mvi a,25 call delay ; ; Resume normal operation by returning old control byte mvi a,9Ch mvi h,0 ;Set TxEna, DTR, RxEna, ErrRst, RTS call osbyte ; *FX 156,oldvalue,0 ; ; Enable centisecond clock (system VIA) lxi h,0FE4Eh ; system VIA interrupt enable register mvi a,0C0H ; enable timer 1 call wrtiom ; write to I/O processor memory ; ret ;done ; ; Routine to write byte in A to I/O processor memory address ; given by HL wrtiom: shld parblk ; store address to parameter block sta parblk+4 ; store data lxi h,parblk ; load hl with address of param block mvi a,6 ; write I/O processor memory call osword ; go do it ret ; parblk: DS 5 ; reserve space for parameter block ENDIF;bbc [22] ; IF disc ;[29] ; This is almost an exact copy of the bbI sendbr routine. ; Modifications to include a long break have been made. ; ; Officially, a "break" is 300 milliseconds of "space" (idle line is ; "mark"). (or maybe 200 milliseconds; I forget.) The timing isn't ; usually that critical, but we'll make an attempt, at least. Sending ; too long a break can cause some modems to hang up. sendlbr: push d ;save d, this may not be necessary, but safe mvi d,17 ;do short break 17 times (approx. 5 sec.) jmp sndbr1 sendbr: push d mvi d,1 ;On short break, do only once ; First, make sure the transmitter is really empty. (The SIO sets ; "transmitter buffer empty" when it can accept another character; ; the previous character is still being shifted onto the line. ; Another status bit, "all done", is set to indicate that the ; transmitter is really idle. sndbr1: mvi a,1 ; select Read Register 1 out mnprts in mnprts ; read the contents ani 1 ; test "all done" flag jz sndbr1 ; loop until it's nonzero. ; ; Next, set the "send break" bit to start the transmitter spacing. mvi a,5 ; select Write Register 5 out mnprts mvi a,0FAH ; Tx enable, 8 bit Tx character, Send Break, out mnprts ; DTR and RTS on. ; ; Now, delay for 30*d hundredths of a second sendbr2: mvi a,30 ; delay count call delay ; The following has been added to allow doing .03 delay d times dcr d ; decrement # of times to do loop jnz sendbr2 ; if not done, do again pop d ; reload d ; ; Time's up. Put transmitter back in normal state (data byte is the ; same as the one in siotbl: for Write Register 5) and return. mvi a,5 ; select Write Register 5 out mnprts mvi a,0EAH ; Tx enable, 8 bit Tx character, out mnprts ; DTR and RTS on. ret ; done. ENDIF ;disc [29] ; ; sysflt - system-dependent filter ; called with character in E. ; if this character should not be printed, return with A = zero. ; preserves bc, de, hl. ; note: ,,, and are always discarded. sysflt: mov a,e ; get character for testing IF mikko cpi 'O'-100O ;Control-O's lock keyboard rnz ; if not control-O, it's ok. xra a ; don't allow control-O out. ENDIF;mikko ret ; mdmflt - modem filter [30] ; called with character to be sent to printer in E ; with parity set as appropriate. ; return with accumulator = 0 do do nothing, ; <> 0 to send char in E. mdmflt: mov a,e ;[30] get character to test ret ; prtflt - printer filter [30] ; called with character to be sent to printer in E ; returns with a = 0 to do nothing ; a <> 0 to print it. ; ; this routine for those printer that automatically insert ; a lf on cr, or cr for lf. Should this be shifted to ; the system indep. stuff, in say 4.06? prtflt: mov a,e ; [30] get character to test ret ; ; system-dependent processing for BYE command. ; for lobo, hang up the phone. sysbye: IF lobo ;[hh] call discon ;[hh] force modem to hang up ENDIF;lobo ret IF lasm LINK CPXSY2.ASM ; If m80 then this ignored ENDIF ; lasm